LaceIT™ Corset LSO
Fitting Instructions
Place handles as close to the closing system as possible.Be sure handles are next to closing system. Stand holding product side panels parallel to floor. Pull outward to fully extend cord.
Place closing system around body, making sure closing system is centered on spine. Supports holding closing system must be equally spaced on each side of spine. Adjust up or down spine to determine best support location.
Once location is determined, pull slightly outward on side panels to maximize open position before using fabric fasteners to close front, right over left.
Pull handles away from fabric fastener and across body, placing handles anywhere on fabric fastener strip encircling side panels once desired support is achieved. Loosen the same way.
User Tips
* Pull handles only slightly at first until you get used to the power.
* Tighten to stand, loosen to sit. You control the tension.
* Pulling in stomach muscles before tightening makes pulling handles easier.
* Do not wear tight for long periods of time unless instructed by physician.
* The product was designed to enable adjustment throughout the day to provide more or less support as
needed.
* To disconnect closing system, simply pull closing system away form fabric fastener. Attach closing system by
placing closing system on fabric fastener.Care Instructions
Remove closing system from side panels. Hand wash in cool water with mild soap. Thoroughly rinse and blot excess water from support with a clean towel. Air dry away from the sun.
____________________________________________________________________
LaceIT™ X640 Low Profile and Standard LSO
Fitting Instructions
Place handles as close to the closing system as possible.Be sure handles are next to closing system. Stand holding product side panels parallel to floor. Pull outward to fully extend cord.
Place closing system around body, making sure closing system is centered on spine. Supports holding closing system must be equally spaced on each side of spine. Adjust up or down spine to determine best supportlocation.
Once location is determined, pull slightly outward on side panels to maximize open position before using fabric fasteners to close front, right over left.
Pull handles away from fabric fastener and across body, placing handles anywhere on fabric fastener strip encircling side panels once desired support is achieved. Loosen the same way.
User Tips
* Pull handles only slightly at first until you get used to the power.
* Tighten to stand, loosen to sit. You control the tension.
* Pulling in stomach muscles before tightening makes pulling handles easier.
* Do not wear tight for long periods of time unless instructed by physician.
* The product was designed to enable adjustment throughout the day to provide more or less support as
needed.
* To disconnect closing system, simply pull closing system away form fabric fastener. Attach closing system by
placing closing system on fabric fastener.
Care Instructions
Remove closing system from side panels. Hand wash in cool water with mild soap. Thoroughly rinse and blot excess water from support with a clean towel. Air dry away from the sun.
____________________________________________________________________________
LaceIT™ X640 Dynamically Self-Adjusting Frame™
Fitting and Care Instructions
ATTACHING THE LACE IT™ LOW,PROFILE AND STANDARD LSO TO THE DYNAMICALLY SELF-ADJUSTING FRAME™Unscrew Secure Slide™ fastener from post, located on posterior side of the Dynamically Self-Adjusting Frame™.
Place LSO around the outside circumference of the Dynamically Self-Adjusting Frame™. Making sure LSO superior edge is facing up.
Align LSO making sure posterior panels Secure Slide™ is centered over Secure Slide™ post, located on the Dynamically Self-Adjusting Frame™.
To fasten LSO to Frame, simply attach Secure Slide™ fastener to post.
Place handles as close to the closing system as possible.
Be sure handles are next to closing system. Stand holding product side panels parallel to floor. Pull outward to fully extend cord.
Place closing system around body, making sure closing system is centered on spine. Supports holding closing system must be equally spaced on each side of spine. Adjust up or down spine to determine best support location.
Once location is determined, pull slightly outward on side panels to maximize open position before using fabric fasteners to close front, right over left.
Pull handles away from fabric fastener and across body, placing handles anywhere on fabric fastener strip encircling side panels once desired support is achieved. Loosen the same way.
User Tips
* Pull handles only slightly at first until you get used to the power.
* Tighten to stand, loosen to sit. You control the tension.
* Pulling in stomach muscles before tightening makes pulling handles easier.
* Do not wear tight for long periods of time unless instructed by physician.
* The product was designed to enable adjustment throughout the day to provide more or less support as
needed.
* To disconnect closing system, simply pull closing system away form fabric fastener. Attach closing system by
placing closing system on fabric fastener.Care Instructions
Remove foam lining from frame. Hand wash in cool water with mild soap. Thoroughly rinse and blot excess water from support with a clean towel. Air dry away from the sun.
____________________________________________________________________
LaceIT™ X640 Anterior Panel
Fitting and Care Instructions
ATTACHING THE LACE IT™ LOW PROFILE AND STANDARD LSO TO THE ANTERIOR PANEL
* Slide anterior panel over left side panel of the brace, make sure vertical elastic strap is facing out.
* Secure anterior panel by attaching two horizontal fabric fasteners to the desired positionLace IT™ L.S.O. Products
Place handles as close to the closing system as possible.
Be sure handles are next to closing system. Stand holding product side panels parallel to floor. Pull outward to fully extend cord.
Place closing system around body, making sure closing system is centered on spine. Supports holding closing system must be equally spaced on each side of spine. Adjust up or down spine to determine best support location.
Once location is determined, pull slightly outward on side panels to maximize open position before using fabric fasteners to close front, right over left.
Pull handles away from fabric fastener and across body, placing handles anywhere on fabric fastener strip encircling side panels once desired support is achieved. Loosen the same way.
User Tips
* Pull handles only slightly at first until you get used to the power.
* Tighten to stand, loosen to sit. You control the tension.
* Pulling in stomach muscles before tightening makes pulling handles easier.
* Do not wear tight for long periods of time unless instructed by physician.
* The product was designed to enable adjustment throughout the day to provide more or less support as
needed.
* To disconnect closing system, simply pull closing system away form fabric fastener. Attach closing system by
placing closing system on fabric fastener.
Care Instructions
Remove closing system from side panels. Hand wash in cool water with mild soap. Thoroughly rinse and blot excess water from support with a clean towel. Air dry away from the sun.